+ Antworten
Ergebnis 1 bis 3 von 3
  1. #1
    Registriert seit
    Jan 2019
    Beiträge
    2

    Question UDP receiver in Pokeys/Poblocks

    hi all,

    I have currently a small project at home, but got stuck at a stage, so was hoping to get some help from the community.

    In essence, I have a Pokeys + Loxone + LED dimmer with driver. I want to send external commands my Loxone via UDP packets, and receive it in Pokeys to command a PWM signal on one of its pwm pins (17-22).

    I know Pokeys have a function block called UDP sender which does the similar thing but in the opposite direction.
    What I need is something like an UDP receiver, but there is no such thing on the Pokeys.
    I tried sending data from Loxone via UDP on port 20057 using some of Pokeys recognized commands such as:
    - I: digital input
    - A: analog input
    - O: digital output
    - E: encoder input
    - C: digital counter input
    - S: EasySensors values
    - P: Pulse engine
    - B: PoBlocks shared slot
    - ':': Modbus ASCII protocol
    - '#': PoLabs simple sensor protocol

    and somehow using PoIL shared slots to send it to a PWM pin, which is connected to a 0-10V PWM dimmer via IRL530N transistor. To accommodate the entire 0-100% duty cycle, I also use an external circuit to translate 0-3.3V from Pokeys to 0-10V to dimmer (schematics in the picture).

    no success so far.

    did you, by any chance, had this kind of scenario and solved it?

    my question exactly is, how do I get a Shared 8/16/32 bit slot to receive external information? where and how do I configure that in Poblocks/Pokeys? my idea was Shared8bit (Shared Slot)-> Output pin22 to dimmer.

    any advice would be greatly appreciated.

    best regards,
    Dima
    Miniaturansichten angehängter Grafiken Miniaturansichten angehängter Grafiken Klicken Sie auf die Grafik für eine größere Ansicht 

Name:	translator.png 
Hits:	32 
Größe:	23.4 KB 
ID:	47355   Klicken Sie auf die Grafik für eine größere Ansicht 

Name:	poblocks.JPG 
Hits:	35 
Größe:	114.2 KB 
ID:	47356  

  2. #2
    Registriert seit
    Jun 2005
    Beiträge
    3,564

    I answer in next time, but i write about this here and i make a PCB with 6 analog out 1-x Volt

    Edit Belo write to a same problem
    Best regards Helmut

    You know my Pokeys Info's ?
    Geändert von Helmut (17.01.19 um 16:58 Uhr) Grund: BeLo

  3. #3
    Registriert seit
    Jan 2019
    Beiträge
    2

    Danke Helmut!

Ähnliche Themen

  1. Pokeys PoBlocks Projekt in ein Anderes kopieren
    Von BeLo im Forum Mikrocontroller
    Antworten: 1
    Letzter Beitrag: 24.10.18, 18:48
  2. Pokeys 57E PoBlocks 1-Wire R/W
    Von andia79 im Forum Mikrocontroller
    Antworten: 6
    Letzter Beitrag: 08.04.18, 07:32
  3. Antworten: 1
    Letzter Beitrag: 31.07.15, 07:47
  4. Antworten: 2
    Letzter Beitrag: 17.03.14, 23:36
  5. Antworten: 12
    Letzter Beitrag: 17.07.13, 22:05

Stichworte