Moin,
ich habe meine pivccu auf pivccu3 aktualisiert, da meine gute alte pivccu Probleme machte. Hab einiges versucht, unter anderem auch ein rpi-update (was wohl keine gute Idee war) - jetzt ist endgültig Schluss: (es ist ein raspi mit aufgesetztem kleinen Funkmodul, hab nur HM Funk - kein wired oder IP)
pivccu-info
piVCCU version: 3.43.16-20
Kernel modules: Not available
Raw UART dev: Not available
Rasp.Pi3 UART: Assigned to GPIO pins
HMRF Hardware: unknown
HMIP Hardware: unknown
Board serial: unknown
Radio MAC: unknown
SGTIN: unknown
State: STOPPED
Infos:
dpkg --get-selections | grep pivccu
pivccu deinstall
pivccu-modules-dkms install
pivccu-modules-raspberrypi install
pivccu3 install
cat /boot/config.txt
For more options and information see
config.txt - Raspberry Pi Documentation
Some settings may impact device functionality. See link above for details
uncomment if you get no picture on HDMI for a default „safe“ mode
#hdmi_safe=1
uncomment this if your display has a black border of unused pixels visible
and your display can output without overscan
#disable_overscan=1
uncomment the following to adjust overscan. Use positive numbers if console
goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16uncomment to force a console size. By default it will be display’s size minus
overscan.
#framebuffer_width=1280
#framebuffer_height=720uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1uncomment to force a HDMI mode rather than DVI. This can make audio work in
DMT (computer monitor) modes
#hdmi_drive=2
uncomment to increase signal to HDMI, if you have interference, blanking, or
no display
#config_hdmi_boost=4
uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=onUncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
Additional overlays and parameters are documented /boot/overlays/README
Enable audio (loads snd_bcm2835)
dtparam=audio=on
dtoverlay=pi3-miniuart-bt
enable_uart=1
force_turbo=1
dtoverlay=pivccu-raspberrypi
Da ist wohl ein echtes Problem:
cat /var/lib/dkms/pivccu/1.0.27/build/make.log
DKMS make.log for pivccu-1.0.27 for kernel 4.19.30-v7+ (armv7l)
Wed 3 Apr 19:05:40 CEST 2019
make -C /lib/modules/4.19.30-v7+/build M=/var/lib/dkms/pivccu/1.0.27/build modules
make[1]: Entering directory ‚/lib/modules/4.19.30-v7+/source‘
Makefile:595: include/config/auto.conf: No such file or directoryERROR: Kernel configuration is invalid.
include/generated/autoconf.h or include/config/auto.conf are missing.
Run ‚make oldconfig && make prepare‘ on kernel src to fix it.Makefile:643: recipe for target ‚include/config/auto.conf‘ failed
make[1]: *** [include/config/auto.conf] Error 1
make[1]: Leaving directory ‚/lib/modules/4.19.30-v7+/source‘
Makefile:23: recipe for target ‚all‘ failed
make: *** [all] Error 2
Da steht ja, was man machen soll - trau mich aber so nicht und versteh auch nicht, wo ich es machen
Hilfe wäre super !
Danke,
Tom